APM 2.8 Flight Controller + 6H GPS + OSD + 433MHz Radio Telemetry Set (6 Pieces)
- Product Code: PKMOjsl0
- Availability: In Stock
Package
Package Type：OEM
Package Contents：1*APM 2.8 Flight Controller, 1*GPS, 1*OSD, 1*Radio Telemetry, 1*Power Module, 1*Shock Absorber Dimensions us | metric
Depth：70 mm
Height：5 mm
Width：40 mm
Product Weight：230 gFastTech
SKU：4108501
DATE LISTED：1/9/2016Details:APM 2.8 flight controller:
The interface is changed from 1.0mm 6P SM06B GPS to DF13-4P I2C external compass interface, put DF13- 5P GPS interface with external compass interface
The I2C interface has been changed to multifunctional MUX interface, users can configurate the interface like UARTO, UART2, I2C, OSD, default OSD interface
2.8 ADOPTS LP2985-3.3, the voltage reaches 16V,increase the reliability, reduce the voltage problem probability of Bad Gyro health
2.8 uses jumper cap to choose, find the MAG pins on board, pluging in jumper cap is built in compass, taking off jumper cap is external compass
2.8 added a 47 uf tantalum capacitor, improve APM on-board chip, the stability of the power supply
GPS:
Compass: 6H
Power supply cable: the default style of APM
Terminal outgoing lines: compatible with APM serial port and I2C port
Telemetry:
Ideal way to setup a telemetry connection between your APM and a ground station
With protection case
Light weight (under 4 grams without antenna)
Frequency: 433MHz
Receiver sensitivity to -121 dBm
Transmit power up to 20dBm (100mW)
Transparent serial link
Air data rates up to 250Kbps
Range of approx 1 mile
MAVLink protocol framing and status reporting
Frequency hopping spread spectrum (FHSS)
Adaptive time division multiplexing (TDM)
Support for LBT and AFA
Configurable duty cycle
Built in error correcting code (can correct up to 25% data bit errors)
Demonstrated range of several kilometers with a small omni antenna
Can be used with a bi-directional amplifier for even more range
Open source firmware
AT commands for radio configuration
Power module (w/ BEC):
Used to test battery voltage and current, flight control board, the two reception battery remaining power calculation, estimate the remaining time of flight
Maximum input voltage 6S, can measure the maximum current is 90A, realize the control of slabs and the voltage of the battery capacity monitoring. Voltage current detection of Dr Official design parameters, design parameters and 3 ground station (mission planer) can directly refer to the official Wiki settings
OSD:
APM has an companion OSD board called MinimOSD. It reads all the MAVLink data in the APM telemetry stream and overlays it on the video stream if you're using an on-board camera and wireless video transmitter. This is useful if you're flying in First Person View (FPV) mode or don't want to use a laptop at the field to see your telemetry data in the Mission Planner
Note:This is an open source module
Package Type：OEM
Package Contents：1*APM 2.8 Flight Controller, 1*GPS, 1*OSD, 1*Radio Telemetry, 1*Power Module, 1*Shock Absorber Dimensions us | metric
Depth：70 mm
Height：5 mm
Width：40 mm
Product Weight：230 gFastTech
SKU：4108501
DATE LISTED：1/9/2016Details:APM 2.8 flight controller:
The interface is changed from 1.0mm 6P SM06B GPS to DF13-4P I2C external compass interface, put DF13- 5P GPS interface with external compass interface
The I2C interface has been changed to multifunctional MUX interface, users can configurate the interface like UARTO, UART2, I2C, OSD, default OSD interface
2.8 ADOPTS LP2985-3.3, the voltage reaches 16V,increase the reliability, reduce the voltage problem probability of Bad Gyro health
2.8 uses jumper cap to choose, find the MAG pins on board, pluging in jumper cap is built in compass, taking off jumper cap is external compass
2.8 added a 47 uf tantalum capacitor, improve APM on-board chip, the stability of the power supply
GPS:
Compass: 6H
Power supply cable: the default style of APM
Terminal outgoing lines: compatible with APM serial port and I2C port
Telemetry:
Ideal way to setup a telemetry connection between your APM and a ground station
With protection case
Light weight (under 4 grams without antenna)
Frequency: 433MHz
Receiver sensitivity to -121 dBm
Transmit power up to 20dBm (100mW)
Transparent serial link
Air data rates up to 250Kbps
Range of approx 1 mile
MAVLink protocol framing and status reporting
Frequency hopping spread spectrum (FHSS)
Adaptive time division multiplexing (TDM)
Support for LBT and AFA
Configurable duty cycle
Built in error correcting code (can correct up to 25% data bit errors)
Demonstrated range of several kilometers with a small omni antenna
Can be used with a bi-directional amplifier for even more range
Open source firmware
AT commands for radio configuration
Power module (w/ BEC):
Used to test battery voltage and current, flight control board, the two reception battery remaining power calculation, estimate the remaining time of flight
Maximum input voltage 6S, can measure the maximum current is 90A, realize the control of slabs and the voltage of the battery capacity monitoring. Voltage current detection of Dr Official design parameters, design parameters and 3 ground station (mission planer) can directly refer to the official Wiki settings
OSD:
APM has an companion OSD board called MinimOSD. It reads all the MAVLink data in the APM telemetry stream and overlays it on the video stream if you're using an on-board camera and wireless video transmitter. This is useful if you're flying in First Person View (FPV) mode or don't want to use a laptop at the field to see your telemetry data in the Mission Planner
Note:This is an open source module